Solare Datensysteme Solar-Log Components Connection Manual Download Page 101 | Manualshive

Page: 101 / 506

background image

101

EEI

24

EEI

24.1

EEI

Termination

Addressing

Interface

No

Yes

LAN

Overview

•

Integrated interface.

•

The inverter‘s IP address has to be assigned.

•

Connected using network cable (patch cable) and Ethernet router or switch.

•

Installation steps:

•

The inverter‘s has to be assigned a static IP address.

•

Switch off the inverters and Solar-Log™.

•

Connect inverters to the Solar-Log™ (RJ45).

•

Connect the inverters to each other (RJ45).

Connect inverters to the Solar-Log™

The wiring is done using a

•

network cable (patch cable/crossover cable) and the

•

Ethernet router or switch.

Connect the inverters to each other

The inverters are connected together using
the RJ45 interface and, if needed, a router or switch.
Connection setup according to the inverter‘s instructions.

Assigning IP addresses

•

A static IP address has to be assigned to the inverter via the display.

•

Please select an IP address with the same class C subnet as the Solar-Log™.
For example: The Solar-Log™ has the IP address 192.168.178.49.
The inverter in this case has to have a free IP address in the same range (from 192.168.178.1 to
192.168.178.254).

•

Procedure: Start according to the inverter‘s instructions.

Detection via the Solar-Log™ WEB Interface

•

For detection on the Solar-Log™ , select the device class under the menu Configuration | Device | Definition |
Interface with the plus symbol and then select EEI as the manufacturer. Confirm your selection with OK.

•

Save your selections and then start the Device Detection under Configuration | Device | Detection.

Detection from the Solar-Log 1200

•

When using the Solar-Log 1200, the detection can also be started from the display. Select the settings ►Start

►

Initial Configuration

►

Page 2 „Device“

►

Add and select the manufacturer EEI from there. Save and start

the Device Detection.

«
...
99
100
101
102
103
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: YOKOGAWA Pages: 74

Compact RDMS Telemetry Receiver-Combiner

Brand: Quasonix Pages: 152

Brand: Extech Instruments Pages: 14

Fridge-tag Ultra Low

Brand: berlinger Pages: 60

KlimaLogg Base 30.5022

Brand: TFA Pages: 72

ebro EBI 20 Series

Brand: Xylem Pages: 36

Brand: Xylem Pages: 40

Brand: SS Telecoms Pages: 37

Brand: Zico Pages: 2

Brand: EasyLog Pages: 2

Logicbus Temp1000Ex

Brand: MadgeTech Pages: 3

Brand: ESPEC Pages: 2

Brand: Lumel Pages: 2

Brand: Fluke Pages: 254

Brand: ZyAura Pages: 3

Brand: HYDROLOGICAL SERVICES Pages: 38

Brand: Ecomatik Pages: 7

Brand: Ecomatik Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands