Solare Datensysteme Solar-Log Components Connection Manual Download Page 72

Page: 72 / 506

Carlo Gavazzi

Carlo Gavazzi

15.1

Carlo Gavazzi - ISMG model

Termination

Addressing

Interface

RS485

Select "Gavazzi ISMG" during the inverter detection.

Overview

•

Integrated interface.

•

Where to connect: RJ45 socket on the outside of the inverter.

•

2-pin wiring.

•

Communication address does not have to be assigned.

Connect inverters to the Solar-Log™

The wiring is done using a

•

ready-made BRJ2 data cable (optional extra; not supplied)

•

self-made, shielded 2 wire data cable and terminal block connector.

Installation steps:

•

Switch off the inverters and Solar-Log™.

•

Connect inverters to the Solar-Log™.

•

Connect the inverters to each other.

Caution

Risk of damage to the unit!
The Solar-Log™ also has an RJ45 socket, which must never be connected to the RJ45 socket on the
inverter.

►

Only connect inverters via the RS485/422 Solar-Log™ interface(s).

Procedure

1. If you are making the cable yourself, connect the wires as shown in the following diagram:

Solar-Log™ terminal strip connector

Inverters

RS485/422 B

RJ 45 socket

►

Pin 7

►

Pin 8

2. Insert the RJ45 plug into any RJ45 socket on inverter 1.
3. Insert the terminal block connector into the Solar-Log™ RS485 socket.

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Search results

Summary of Contents for Solar-Log

Reviews:

Related manuals for Solar-Log

Brands by name

Popular brands

Solare Datensysteme Solar-Log, Components Connection Manual

Search results

Summary of Contents for Solar-Log

Reviews:

Related manuals for Solar-Log

Brands by name

Popular brands