Solare Datensysteme Solar-Log Components Connection Manual Download Page 179 | Manualshive

Page: 179 / 506

background image

179

Kaco

48

Kaco

48.1

Kaco - Powador

Termination

Addressing

Interface

Yes

Yes

RS485

Overview

•

Integrated interface

•

Where to connect: Terminal strip inside the inverter

•

2-pin wiring

•

Communication address must be allocated

•

Installation steps

•

Switch off the inverters and Solar-Log™

•

Connect inverters to the Solar-Log™

•

Connect the inverters to each other

•

Allocate communication address

Note

Instructions and a diagram for wiring Kaco Powador inverters together are in the appendix.

Connect inverters to the Solar-Log™

The wiring is done using a

•

partly made data cable (optional extra; not supplied)

or

•

self-made, shielded 2 wire data cable and terminal block connector.

Procedure

1.  Open the inverter as shown in the inverter's instructions.
2.  Pull the free wires through the wire opening in the inverter.
3.  If you are making the cable yourself, connect the wires as shown in the following diagram:

Solar-Log™ terminal strip connector

Inverter terminal strip

Terminal

Terminal

►

1

►

B

►

4

►

A

4. If no further inverter connected, terminate the inverter:

Series 2 Powador: Set the DIP switch inside the inverter to ON and all other inverters to OFF.

5. Close the inverter if no other inverters are to be connected.
6. Insert the terminal block connector into the Solar-Log™ RS485 socket.

«
...
177
178
179
180
181
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: WatchDog Pages: 8

Brand: Oceasoft Pages: 20

OM-CP-HITEMP140-FP

Brand: Omega Pages: 7

Brand: Digi-Sense Pages: 8

METPOINT BDL portable

Brand: Beko Pages: 108

Brand: Racelogic Pages: 36

Brand: Kvaser Pages: 30

Brand: Triplett Pages: 7

Brand: Triplett Pages: 8

Brand: Triplett Pages: 15

Brand: Tzone Pages: 13

Brand: socomec Pages: 2

Brand: socomec Pages: 26

Brand: ELPRO Pages: 20

Matman Combi-USB

Brand: ELTEX Pages: 2

Squirrel 1000 Series

Brand: Eltek Pages: 67

Brand: AEM Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands