Solare Datensysteme Solar-Log Components Connection Manual Download | Manualshive

Page: 78 / 506

background image

78

Chint Power

16.2

Chint Power (CPS 20k+)

Termination

Addressing

Interface

Yes

Yes

RS485

Overview

•

Integrated interface.

•

Where to connect: RJ45 socket on the outside of the inverter.

•

2-pin wiring.

•

The communication addresses (1-32) have to be assigned.

•

Installation steps:

•

Switch off the inverters and Solar-Log™.

•

Connect inverters to the Solar-Log™.

•

Connect the inverters to each other.

Select the Chint inverter during the initial configuration.

Connect inverters to the Solar-Log™

The wiring is done using a

•

self-made cable connection with RS485 data cable and terminal block connector.

Procedure

Caution

Risk of damage to the unit!
The Solar-Log™ also has an RJ45 socket, which must never be connected to the RJ45 socket on the
inverter.

►

Only connect inverters via the RS485/422 Solar-Log™ interface(s).

1. Connect wires as shown in the diagram below:

Solar-Log™ terminal strip connector

RJ45 inverter

Terminal

PIN

►

1

►

1-485+

►

4

►

3-485-

2.  Insert the RJ45 plug into any RJ45 socket on inverter 1.
3.  If no further inverter is connected, terminate the inverter according to the instructions for the inverter.
4.  Insert the terminal block connector into the Solar-Log™ RS485 socket.

Connect the inverters to each other

•

Connect using a network cable (patch cable).

•

Where to connect: RJ45 socket on the outside of the inverter.

«
...
76
77
78
79
80
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: Jetter Pages: 66

Brand: 3nStar Pages: 19

Brand: JASTEC Pages: 13

Brand: EasyLog Pages: 5

Brand: Canary Pages: 44

Logicbus Temp1000Ex

Brand: MadgeTech Pages: 3

Ultra 2 TGU-4550

Brand: Tinytag Pages: 2

Brand: TempSen Pages: 25

Brand: TRAMEX Pages: 2

Brand: SEFRAM Pages: 12

Brand: SIAP+MICROS Pages: 29

Brand: Marathon Pages: 2

Brand: Measurement Computing Pages: 22

Brand: Measurement Computing Pages: 29

Brand: Measurement Computing Pages: 29

Brand: Measurement Computing Pages: 36

Brand: Measurement Computing Pages: 48

Tinytag Connect

Brand: Intab Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands