Solare Datensysteme Solar-Log Components Connection Manual Download Page 297 | Manualshive

Page: 297 / 506

background image

297

SMA

84.3

Connect SMA with original SMA RS485 piggy back and the SMA RS485

data module

Termination

Addressing

Interface

Resistor jumper

No

RS485

Select “SMA: Data1“ for the device detection.

Overview

•

Interface not integrated; retrofit the SMA RS485 piggyback card

•

Where to connect: Terminal strip inside the inverter on the piggyback

•

Communication address does not have to be assigned

•

3-pin wiring

•

Installation steps

•

Switch off the inverters and Solar-Log™

•

Installing the original SMA RS485 piggyback in the inverter

•

Connect inverters to the Solar-Log™

•

Connect the inverters to each other

Installing the original SMA RS485 piggyback in the inverter

Procedure

►

Install the original SMA RS485 piggy back in the inverter in accordance with the interface card installation
instructions.

Connect inverters to the Solar-Log™

The wiring is done using a

•

ready-made data cable (optional extra; not supplied)

or

•

self-made, shielded 3 wire data cable and terminal block connector.

Procedure

1.  Open the inverter as shown in the inverter's instructions.
2.  Pull the free wires through the wire opening in the inverter.
3.  Pull the cable through the insulation tube.

Note

The wire must be enclosed in the insulating hose inside the inverter.

4. If you are making the cable yourself, connect the wires as shown in the following diagram:

Solar-Log™ terminal strip connector

Inverter terminal strip

Terminal

Terminal

►

1

►

2

►

3

►

5

►

4

►

7

«
...
295
296
297
298
299
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: Acclima Pages: 18

Brand: UNDATEC Pages: 20

Brand: Onset Pages: 4

Brand: LEGRAND Pages: 16

Brand: IBA Pages: 27

Brand: Danelec Marine Pages: 31

microSpider2 Industrial

Brand: Halytech Pages: 8

Brand: Klipspringer Pages: 2

Brand: Kamstrup Pages: 20

OM-EL-WiFi Series

Brand: Omega Pages: 2

Brand: Steinberg Pages: 13

Brand: REED Pages: 16

Brand: Newland Pages: 33

Brand: Newland Pages: 60

Brand: Newland Pages: 66

Brand: Newland Pages: 69

Brand: Egnite Pages: 102

Brand: Egnite Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands