Solare Datensysteme Solar-Log Components Connection Manual Download Page 487 | Manualshive

Page: 487 / 506

background image

487

Sensor Box Professional Plus

Connection plug Solar-Log™

Sensor Box Professional Plus

►

1 (Data+)

►

Data+ A (brown)

►

2 (+12V)

►

+12V (red)

►

3 (GND)

►

GND (black)

►

4 (Data-)

►

Data- B (orange)

3.5

Starting Up at the Solar-Log™

By switching-on the Solar-Log™, it will provide power to the Sensor Box Professional Plus. Afterwards, the Sensor
Box Professional Plus must be configured to the free RS485-port:

•

Open the dialogue

Configuration | Devices | Definition | Interfaces

in the WEB menu of the Solar-Log™.

Please refer to the Installation Manual in chapter “Connecting accessories”, “Installation” and “Configuring
connected devices”.

•

Select under Devices class „Sensor“ and under Manufacturer „M&T Sensor“.

•

Carry out device detection.

The Sensor Box Professional Plus is integrated with the system in the same way as an inverter. The further confi-
guration could be handled with the Solar-Log™ web interface.

3.6

Technical Data

Sensor Box Professional Plus

Dimensions, weight

W/H/D in mm: 145/85/40, 360 g

Housing

Powder-coated aluminum

Protection mode

IP65

Operating temperature

-20 °C to +70 °C

Power supply

Via RS485 data cable from Solar-Log™ (10,5-28 VDC),

Supply current

Typical 10 mA

Communication Port

RS485

Protocol

Solar-Log™, 9600 Baud, 8N1

Irradiance

Irradiance : ± 5 % (0 W/m2 to 1400 W/m2 )

Cell-temperature: ± 1K (-20 °C to +70 °C) / ± 2 K (-40 °C to +85 °C)

Installation

with screws on the substructure

Connection cable

•

4 pole, 3 m (10 feet), weather and uv resistant (LiY(St) 11 Y (4 x 0,14)

•

prolongable up to 50 m (165 feet)

Conformity

CE :DIN EN-61000-6-1:2007 and DIN EN-61000-6-3:2007

«
...
485
486
487
488
489
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: Kelvin Pages: 4

VBOX Micro RLVBMIC01

Brand: Racelogic Pages: 29

LM-U PRO Series

Brand: G-Tek Pages: 21

Brand: Racelogic Pages: 4

Brand: Dwyer Instruments Pages: 2

Brand: Theodor Friedrichs Pages: 170

Brand: T&D Pages: 2

Performance Box Touch V1

Brand: Racelogic Pages: 7

Brand: Radionode Pages: 53

CTD-Diver DI28 Series

Brand: Van Essen Pages: 34

Brand: Dataq Pages: 62

CSI-GL-LAN-STICK

Brand: CanadianSolar Pages: 11

16 MB KeyGrabber Nano

Brand: KeeLog Pages: 20

Brand: RBR Pages: 7

Dialock MDU 100

Brand: Hafele Pages: 216

Brand: SWR SCIENCE Pages: 123

Brand: MadgeTech Pages: 2

Brand: MadgeTech Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands