Solare Datensysteme Solar-Log Components Connection Manual Download Page 49 | Manualshive

Page: 49 / 506

background image

49

Albatech

7

Albatech

7.1

Albatech APL Trifase 15 / 20

Termination

Addressing

Interface

Jumper

Yes

RS485

Inverters from different Albatech model ranges (APL monophase / triphase) cannot be mixed on an RS485 connec-
tion. The correct range must be selected when selecting inverters.

Overview

•

Integrated interface.

•

Where to connect: Terminal strip inside the inverter.

•

3-pin wiring.

•

Communication address must be allocated.

•

Installation steps:

•

Allocate communication address.

•

Switch off the inverters and Solar-Log™.

•

Connect inverters to the Solar-Log™.

•

Connect the inverters to each other.

Note

If more than 32 inverters are connected a signal amplifier must be installed in the RS485 bus in accor-
dance with the manufacturer.

Connect inverters to the Solar-Log™

The wiring is done using a

•

self-made, shielded 3 wire data cable and terminal block connector.

It is connected to the inverter as shown in the following diagram. The inverters are terminated on pin 9/10 of J1.
Both the first and also the last inverter must be terminated.

Fig.: Albatech APL block connector

«
...
47
48
49
50
51
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Process101A 20mA

Brand: MadgeTech Pages: 2

Brand: MadgeTech Pages: 2

Brand: MadgeTech Pages: 2

RMS Wall mount Data Logger

Brand: Rotronic Pages: 35

Brand: MadgeTech Pages: 2

OctProcess Series

Brand: MadgeTech Pages: 2

Brand: MadgeTech Pages: 2

Bridge120 Series

Brand: MadgeTech Pages: 2

Brand: MadgeTech Pages: 4

Brand: MadgeTech Pages: 4

Brand: MadgeTech Pages: 4

Brand: MadgeTech Pages: 4

Brand: MadgeTech Pages: 4

CurrentX Series

Brand: MadgeTech Pages: 4

MadgeNet RFRHTemp2000A

Brand: MadgeTech Pages: 16

MadgeNET RFTCTemp2000A

Brand: MadgeTech Pages: 16

Brand: MadgeTech Pages: 2

Brand: MadgeTech Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands