Saluki S1465 Series User Manual Download Page 8

Page: 8 / 243

Tel: 886.909 602 109 Email: [email protected]

www.salukitec.com

Content

..................................................................................................................................................................

1.1 General

..........................................................................................................................................................

1.2 Safety guide

..................................................................................................................................................

2 Start Guide

.............................................................................................................................................................

2.1 Preparation before use

................................................................................................................................

2.2 Description of front and rear panels

..............................................................................................................

2.3 Basic configuration method

.........................................................................................................................

2.4 Data management

......................................................................................................................................

3 Operation Guides

...................................................................................................................................................

3.1 Basic operation guides

................................................................................................................................

3.2 Advanced operation guides

.........................................................................................................................

4 Menu

......................................................................................................................................................................

4.1 Menu structure and parameter settings

.........................................................................................................

4.2 Menu description

......................................................................................................................................

122

5 Remote Control

....................................................................................................................................................

176

5.1 Remote control Basis

................................................................................................................................

176

5.2 Remote interface and its configuration

........................................................................................................

189

5.3 Basic programming method of the VISA interface

........................................................................................

191

5.4 I/O library

.................................................................................................................................................

195

6 Fault Diagnosis & Repair

......................................................................................................................................

197

6.1 Operating principle

....................................................................................................................................

197

6.2 Fault diagnosis and troubleshooting

...........................................................................................................

198

6.3 Error information

.......................................................................................................................................

203

6.4 Repair methods

........................................................................................................................................

204

7 Test Methods

.........................................................................................................................................................

206

Appendix A Explanations of Terms

.............................................................................................................................

218

Appendix B Lookup Table of SCPIs

............................................................................................................................

226

Appendix C Lookup Table of Error Information

.............................................................................................................

242

Appendix D Lookup Table of PC Keyboard in Function Configuration Windows

..............................................................

243

Summary of Contents for S1465 Series




















































































































































































































































Search results

Summary of Contents for S1465 Series

Reviews:

Saluki S1465 Series, User Manual, Page: 8 / 243

Search results

Summary of Contents for S1465 Series

Reviews: