![background image](http://html1.mh-extra.com/html/rainbow/turbo-carnival-clubhouse/turbo-carnival-clubhouse_assembly-instructions-manual_3449621071.webp)
Swing Beam Installation
1. Attach Swing Hangers
(N26)
to Swing Beam
(7084) (7085) (7154) (7821)
using 3/8" Hardware
(H3)
(H11) (H24) (H28) (H135)
and 3/8" Bolt Cup
(N29)
.
*SUGGESTION: Use a box wrench to hold on to Hex Head Bolts (H135).
2. Position Rainbow Plaque
(N83)
in the approximate position shown and attach to Swing Beam
using #10 Hardware
(H157)
(as shown in Detail A).
3. Bolt together Lower A-Frame Block
(6007)
, Upper A-Frame Block
(6008)
, and both 90° Brackets
(N46)
using 1/2" Hardware
(H4) (H12) (H18) (H29) (H72)
and 3/4" Hardware
(H5)
.
*NOTE: Mounting holes in all vinyl coated pieces must be cleaned out with a utility knife
before installation.
4. Attach A-Frame Legs
(7129)
to A-Frame Block assembly using both 45° Brackets
(N55)
and 1/2"
Hardware
(H4) (H12) (H18) (H29) (H151)
.
*NOTE: Lay assembly on the ground with A-Frame Legs (7129) pointing in opposite directions
with offset holes up. Do not tighten hardware at this time.
5. Place Swing Beam Assembly in position between the 90° Brackets
(N46)
and attach using 1/2"
Hardware
(H4) (H12) (H18) (H29) (H72)
and 3/4" Hardware
(H5)
through both 45° Brackets
(N55)
.
6. Attach both 90° Brackets
(N46)
to the Swing Beam
(7084) (7085) (7154) (7821)
using 3/8" Hardware
(H116)
and 3/8" Bolt Cup
(N29)
.
7. Position Swing Beam Plate
(N56)
over the holes in the Top Joist with Swing Holes
(6131)
and attach
using 1/2" Hardware
(H4) (H12) (H18) (H29) (H65) (H76)
and 3/4" Hardware
(H5)
through
holes 1 and
3 only
.
*NOTE: Do not tighten Hardware at this time.
8. Lift Swing Beam assembly into position on top of the Swing Beam Plate
(N56)
and attach using
1/2" Hardware
(H4) (H12) (H18) (H29) (H72) (H76)
and 3/4" Hardware
(H5)
.
*NOTE: For ease of installation, insert Carriage Bolt (H76) through the Swing Beam (7084)
(7085) (7154) (7821), and then insert Carriage Bolt (H72). Do not tighten hardware at
this time.
9. Lift Swing Beam assembly up until A-Frame Legs hold Swing Beam in a level position.
CAUTION: Use two people to lift Swing Beam assembly. Legs will close inward as Swing
Beam is lifted into position. Legs are very unstable until Cross Member is installed.
*NOTE: Tighten Hex Head Bolt (H151) that goes through A-Frame Legs (7129) and A-Frame
Block assembly from #3 and all hardware that goes through Swing Beam Plate (N56) at
this time.
10. Hold A-Frame Cross Member
(7145)
in a level position against A-Frame Legs, and drill through A-
Frame Legs
(7129)
using a
9/16" drill bit
. Attach Cross Member using 1/2" Hardware
(H4) (H12)
(H18) (H29) (H72)
and 3/4" Hardware
(H5)
.
11. Attach A-Frame Legs
(7129)
to A-Frame Blocks using 3/8" Hardware
(H3) (H119)
.
12. Attach Swing options to Swing Hangers
(N26)
using Spring Clips
(N90)
.
13. Insert Rope through end hole in Swing Beam
(7084) (7085)
and tie a double knot. Tie single knots in
3 places. Insert bottom of Rope through Swing Disk
(N91)
or Rope Buoy
(N92)
and tie a double knot.
14. Inflate Buoy Ball using Buoy Ball inflator.
*NOTE: Swing Disk or Buoy Ball should be a minimum of 8" off the ground.
!
WARNING: When Swing Beam is fully assembled, make sure the Swing Beam is level to
avoid serious injury.
!
Continued on next page:
70
Step 28