Radwin 5000 HPMP, User Manual

Page: 480 / 518

RADWIN 5000 HPMP User Manual Release 3.5.70 C ‐ 61
Private MIB Parameters
winlink1000IduSrvEthThroughput RO Current available Ethernet service throughput in
bps.
winlink1000IduSrvEthMaxInfoRate RW Holds the maximum bandwidth (kbps) to be
allocated for Ethernet service. Value of zero
means that Ethernet service works as best
effort. The maximum value is product specific.
Refer to the user manual.
winlink1000IduSrvAvailableTrunksT
1 RO A bitmap describing the TDM trunks that can be
opened under T1 configuration. The values
take into account the IDU hardware
configuration the air rate and the installation
range.
winlink1000IduEthernetIfTable N/A IDU Ethernet Interface table.
winlink1000IduEthernetIfEntry N/A IDU Ethernet Interface table entry. INDEX {
winlink1000IduEthernetIfIndex }
winlink1000IduEthernetIfIndex RO If Index corresponding to this Interface.
winlink1000IduEthernetIfAddress RO IDU MAC address.
winlink1000IduEthernetNumOfLan
Ports RO Number of LAN interfaces in the IDU.
winlink1000IduEthernetNumOfSfpP
orts RO The number of SFP interfaces in the IDU.
winlink1000IduEthernetSfpProperti
es RO SFP venfor properties : Vendor Name PN and
Revision.
winlink1000IduEthernetGbeSuppor
ted Supported Giga bit Ethernet in IDU.
winlink1000IduEthernetOduInError
s RO The number of inbound packets that contained
errors preventing them from being deliverable
to a higher ‐ layer protocol.
winlink1000IduBridgeTpAging RW Timeout in seconds for aging. Note that for this
parameter to be effective the ODU must be
configured to HUB mode. A change is effective
immediately.
winlink1000IduTdmTxClockAvailStat
es RO Available states of the TDM Transmit Clock
Control each input status is represented by a
bit. When the state is available the bit value is
1. When the state is unavailable the bit value
is 0. The available states are: bit 2 =
Transparent bit 3 = Local Loop Timed bit 4 =
Remote Loop Timed bit 5 = Local Internal bit 6
= Remote Internal
winlink1000IduTdmTxClockDesiredS
tate RW Required state of the TDM Transmit Clock
Control. A change is effective after re ‐ activation
of the TDM service.
winlink1000IduTdmTxClockActualSt
ate RO Actual state of the TDM Transmit Clock Control.
winlink1000IduTdmMasterClockAva
ilOptions RO Available options of the TDM Master Clock
Control each input status is represented by a
bit. When the option is available the bit value
is 1. When the option is unavailable the bit
value is 0. The available options are: bit 2 =
Automatic bit 3 = Trunk #1 bit 4 = Trunk #2 bit
5 = Trunk #3 bit 6 = Trunk #4 When no options
are available the returned value is: 1
winlink1000IduTdmMasterClockDes
ired RW Required TDM Master Clock. A change is
effective after re ‐ activation of the TDM service.
winlink1000IduTdmMasterClockAct
ual RO Actual Trunk used for TDM Master Clock.
winlink1000IduTdmConfigTable N/A IDU TDM Links Configuration table.
Table C ‐ 3: Private MIB Parameters ‐ HSU (Sheet 23 of 33)
Name OID Type
A
cce
ss
Description