PerkinElmer OilExpress 4 User Manual Download Page 65

Page: 65 / 152

Overview of the OilExpress 4 System . 65

17.

The autosampler arm moves the disposable tips to the first available empty waste tip

location, and the two used tips are dropped into positions 1 and 3.

18.

The autosampler moves to the first available clean tip and loads a disposable tip on

VersaTips 1 and 3 from the next two available positions.
These are collected from positions 2 and 4.

19.

The autosampler returns to the injection station and positions VersaTips 2 and 4 over

Fill Cups 1 and 2.

20.

When the spectrum has been collected, the FCM draws the sample to its internal waste

container.
The spectrometer status is

Idle

. The liquid presence sensor LED changes from green to

red.

Summary of Contents for OilExpress 4

























































































































































Search results

Summary of Contents for OilExpress 4

Reviews:

Related manuals for OilExpress 4

Brands by name

Popular brands

PerkinElmer OilExpress 4, User Manual

Search results

Summary of Contents for OilExpress 4

Reviews:

Related manuals for OilExpress 4

Brands by name

Popular brands