manualshive.com logo in svg

PerkinElmer OilExpress 4, User Manual

Share
Download
PerkinElmer OilExpress 4 User Manual Download Page 134

134 . OilExpress 4 System User's Guide 

Sample not loaded into the 

flow cell during a System 

Check or Load operation 

Sample was not in correct 

position on the autosampler deck 

Check that all sample racks are 

located correctly on the deck for 

the current system configuration. 

Ensure that all sample containers 

are loaded into the sample racks in 

the correct sampling order 

Actual height of sample in 

container does not correspond to 

sampling height in the software 

Check the System Check sampling 

height on the Autosampler Setup 

dialog  

OR 

Check the Load sampling height on 

the Autosampler Control screen 

Problems with sample 

preparation: 

Sample is outside the viscosity 

range supported by the system 

Sample contains large particles 

Check the viscosity of the sample. 

Ensure that the sample was filtered 

to remove any large particles 

Refer to

 Sample Preparation

 on 

page 73 

Liquid presence sensor is not 

connected to the rear of the FCM 

NOTE: The LED on the liquid 

presence sensor is not lit 

Disconnect the FCM from mains 

power and then connect the liquid 

presence sensor. Refer to 

Electrical 

Connections on the FCM

 on 

page 50 

Then reconnect the FCM to the 

mains power  

DO NOT connect the liquid 

presence sensor while the FCM is 

connected to mains power 

Tubing from injection station is 

not seated correctly inside the 

sensor  

Check that the tubing is seated 

correctly in the liquid presence 

sensor 

Refer to 

Removing and Installing 

the Flow Cell

 on page 97 

Liquid presence sensor failure 

NOTE: The LED does not 

change to green when 

the sample reaches the 

sensor, or is always 

green 

Check that the sensor is correctly 

connected to the rear of the FCM 

If this fails to resolve the issue, 

contact your PerkinElmer Service 

Representative 

 

Air is leaking into the system 

Check all the connections to valves 

and syringes, the injection station 

and the flow cell. Prime the system 

until there is no air in the tubing 

Summary of Contents for OilExpress 4

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands