PerkinElmer OilExpress 4 User Manual Download Page 130

Page: 130 / 152

130 . OilExpress 4 System User's Guide

FCM fails fit-for-purpose test

(continued)

FCM hardware failure

Contact your PerkinElmer Service

Representative

Provide the log file for the FCM

that failed, if required

Refer to

Fluid Control Module

page 48

Valve or Pump failure

–

Possible short circuit or

overcurrent

FCM hardware failure

Contact your PerkinElmer Service

Representative

Ultrasonic Liquid Level

Sensor Bar fails to calibrate

Items on deck other than

allowed labware

Check that the labware is located

in the correct positions for the

current configuration

Clear the deck of any obstruction

Items off deck, to the left of the

calibration bar

Remove any items

Sensor bar hardware failure

Contact your PerkinElmer Service

Representative

Ultrasonic Liquid Level

Sensor Bar fails to detect

heights

Sample level too low

Check that all sample levels are

above the minimum height for the

sample container

Sample not present

Ensure that all containers contain

samples and are loaded into the

sample racks in the correct

sampling order

Sensor bar is not connected to

the PC (via additional card)

Ensure that the sensor bar is

connected to the USB expansion

card fitted to the PC

Sensor bar hardware failure

Contact your PerkinElmer Service

Representative

System liquid tubing contains

air after priming

System liquid tubing is not

immersed in system liquid

Check the tubing is immersed in the

system liquid. Refill the system

liquid container, if required

Use the Prime button on the

Autosampler Control dialog to

Prime system 2–3 times more (until

there is no air in the tubing) before

running a batch. Refer to

Priming

the System

on page 74

Summary of Contents for OilExpress 4

























































































































































Search results

Summary of Contents for OilExpress 4

Reviews:

Brands by name

Popular brands

PerkinElmer OilExpress 4, User Manual

Search results

Summary of Contents for OilExpress 4

Reviews:

Brands by name

Popular brands