manualshive.com logo in svg

PerkinElmer OilExpress 4, User Manual

Share
Download
PerkinElmer OilExpress 4 User Manual Download Page 19

Warnings and Safety Information . 19 

OilExpress 4 System Safety Summary 

This equipment must be used only by authorized personnel in a well-ventilated laboratory 

environment. 

The PerkinElmer OilExpress 4 System has been designed to comply with a wide variety of 

international standards governing the safety of laboratory equipment. Refer to the product 

certificates and declaration of conformity documents supplied with the components of your 

OilExpress 4 System for the relevant compliance information. 

In routine use, the OilExpress 4 System poses virtually no risk to you. If you take some 

simple, common-sense precautions, you can make sure that you maintain the continued safe 

operation of the OilExpress 4 System. 

•

 

DO make sure that the OilExpress 4 System is properly connected to the electrical 

supply; in particular make sure that the ground (earth) is securely connected. 

•

 

DO take care with solvents: heptane is highly flammable. Fill the system liquid container 

away from the OilExpress 4 System and any heat sources or other electrical systems. 

Always keep the lid on the system liquid and waste liquid containers. 

•

 

The system waste liquid container must be vented externally or connected to an 

extraction system. 
A connector for 6 mm (internal diameter) tubing is fitted to the lid supplied with the 

waste container for the OilExpress 4 System.  

•

 

DO NOT place any part of the body beyond the safety shield the front of the 

autosampler enclosure whilst operating the OilExpress 4 System. 

•

 

DO disconnect the electrical power cable before opening any ports or covers in the 

system, unless otherwise directed in the maintenance procedures described in this 

manual or in the software. 

•

 

DO NOT open the main cover of any of the components of the instrument, unless 

directed in the maintenance procedures.  

•

 

DO keep the spectrometer dry. Avoid spilling liquid onto the instrument. Clean all 

external spills immediately.  

Read the more detailed information about warnings and safety in the following pages, and in 

the documentation supplied with your spectrometer, to ensure the safe operation of the 

instrument. 

 

Summary of Contents for OilExpress 4

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands