PerkinElmer OilExpress 4 User Manual Download Page 51

Page: 51 / 152

Overview of the OilExpress 4 System . 51

Fluid connections on the FCM

The fluid connections on the rear of the FCM are shown in Figure 31 (shown with the

connectors installed in the mounting block). Fluid tubing connections on the rear of the FCM

connect the upper (outlet) port on the flow cell to the waste transfer container (WTC) in the

FCM, and the WTC to the external waste liquid container.

The EXHAUST outlet vents solvent vapor from the pump to the waste container. Ensure that

the waste liquid container is lower than the FCM so that any vapor condensing in the line will

drain to the container. The waste liquid container should be vented to a suitable outlet.

Figure 31 Fluid connections on the FCM

CELL (from the flow cell)

EXHAUST (to waste container)

WASTE (to waste container)

Summary of Contents for OilExpress 4

























































































































































Search results

Summary of Contents for OilExpress 4

Reviews:

Related manuals for OilExpress 4

Brands by name

Popular brands

PerkinElmer OilExpress 4, User Manual

Search results

Summary of Contents for OilExpress 4

Reviews:

Related manuals for OilExpress 4

Brands by name

Popular brands