manualshive.com logo in svg

PerkinElmer OilExpress 4, User Manual

Share
Download
PerkinElmer OilExpress 4 User Manual Download Page 6

6 . OilExpress 4 System User's Guide 

About this Manual 

NOTE: The OilExpress 4 Oil Condition Monitoring System must be installed by a PerkinElmer 

Service Representative. This guide does not contain installation instructions. 

This user guide covers FT-IR analysis using OilExpress 4 software only. Refer to the 

OilPrep 

Oil Dilution System Operation Manual 

(Document Number 8860042) for information about 

using WinPREP software for oil dilution. 

NOTE: This user manual provides user instructions for the OilExpress 4 System (including 

the Spectrum Two spectrometer and the autosampler).  

 

You are also supplied with the 

JANUS® Automated Liquid Handling System User 

Manual

 (Document Number 1694282) and the 

Spectrum Two User’s Guide

 

(part number L1050228). These documents are provided for your reference. 

However, operating and customer-maintenance procedures described in those 

manuals are superseded by those covered in this document, unless stated otherwise. 

 

For all other procedures you should contact your PerkinElmer Service Representative. 

Using this Guide 

This guide describes how to use your OilExpress 4 System and perform any customer-maintenance 

tasks. We recommend that you use it as follows: 

1.

 

Read the 

Warnings and Safety Information

 starting on page 17 before using your 

OilExpress 4 System. 

2.

 

Read 

Overview of the OilExpress 4 System

 starting on page 27 to learn about the 

components of the system. 

3.

 

Read

 Getting Started with OilExpress 4 

starting on page 66 to learn how to run an 

analysis and modify some basic software parameters. 

NOTE: Refer to the on-screen Help system available from the Help menu in the OilExpress 4 

software for full information about using the software. 

4.

 

Read 

Maintenance and Troubleshooting 

starting on page 95 to learn what  

customer maintenance the OilExpress 4 System requires. 

If you want to learn more about the information that can be obtained by analyzing used oils 

and the analysis methods provided with OilExpress 4, read 

Introduction to Oil Analysis by 

Infrared Spectroscopy

 starting on page 10. 

Summary of Contents for OilExpress 4

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands