PerkinElmer OilExpress 4 User Manual Download Page 31

Page: 31 / 152

Overview of the OilExpress 4 System . 31

For FT-IR analysis using OilExpress 4 software, two of the VersaTips are dedicated to

aspirating samples for analysis using wide-bore disposable tips (VersaTips 1 and 3). The

other two are dedicated to dispensing system liquid, for example to clean the flow cell

(Figure 6).

Figure 6 VersaTips 1 and 3 (with disposable tips) are used for sampling;

VersaTips 2 and 4 are used for dispensing system liquid

For systems running in the dual FT-IR analysis and oil dilution mode, VersaTips 1, 2, 3 and 4

are used with disposable tips for oil sampling. VersaTips 1 and 3 are used without tips to

dispense solvent for dilution. VersaTips 2 and 4 will be used to dispense system liquid to

clean the flow cell.

System Liquid Container(s)

WARNING

In the event of a solvent spillage, isolate the power to the OilExpress 4

System components immediately and then clean up the solvent spill.

The system liquid container must be placed next to the autosampler in a location where it

will not be knocked over.

NOTE: The system liquid container available with the OilExpress 4 system is 2 L

(part number L9004516) and the waste container is 5 L (part number L9004517).

Summary of Contents for OilExpress 4

























































































































































Search results

Summary of Contents for OilExpress 4

Reviews:

Related manuals for OilExpress 4

Brands by name

Popular brands

PerkinElmer OilExpress 4, User Manual

Search results

Summary of Contents for OilExpress 4

Reviews:

Related manuals for OilExpress 4

Brands by name

Popular brands