PerkinElmer OilExpress 4 User Manual Download Page 117

Page: 117 / 152

Maintenance and Troubleshooting . 117

14.

Screw the blue nut connector from the tubing from the lower port of the flow cell into a

red Luer-lok connector.

15.

Connect the tubing from the lower port of the flow cell to the appropriate fill cup on the

injection station.
For a single-spectrometer system, the tubing is connected to Fill Cup 1 (shown in

Figure 67), which is to the rear of the autosampler deck. For a DUO (dual-spectrometer)

system, lower flow cell is connected to Fill Cup 1, and the upper flow cell is connected

to Fill Cup 2.
Push the Luer-lok connector into the connection on the injection station, then turn the

lock hub on the Luer-lok connector approximately one half-turn clockwise Figure 68).

Figure 67 Connecting tubing to Fill Cup 1

Figure 68 Tubing connected to Fill Cup 1

Summary of Contents for OilExpress 4

























































































































































Search results

Summary of Contents for OilExpress 4

Reviews:

Related manuals for OilExpress 4

Brands by name

Popular brands

PerkinElmer OilExpress 4, User Manual

Search results

Summary of Contents for OilExpress 4

Reviews:

Related manuals for OilExpress 4

Brands by name

Popular brands