manualshive.com logo in svg

PerkinElmer OilExpress 4, User Manual

Share
Download
PerkinElmer OilExpress 4 User Manual Download Page 64

64 . OilExpress 4 System User's Guide 

12.

 

The disposable tips are lowered into the fill cups to form a seal and the syringe pump 

dispenses the sample to the fill cup. 

 

13.

 

The liquid presence sensors detect the presence of the samples in the tubing to the flow 

cell. 
Each liquid presence sensor detects the presence of the front of the liquid moving 

through the tubing from the fill cup, and sensor LED changes from red to green. The 

time taken for the liquid to reach the sensor is used by the OilExpress 4 software to 

calculate parameters, such as the time required for the FCM to pump the sample into 

the flow cell and the adaptive cleaning settings.  

 

Only 700 µl of sample is dispensed to the cell. 

14.

 

When the sample is detected, if required the FCM draws the sample into the flow cell. 

15.

 

The sample spectra are collected.  
The autosampler status is 

Preparing

. The spectrometer status is 

Scanning

.  

16.

 

During the sample measurement, the autosampler moves the disposable tips over the 

waste trough on the injection station, and any excess oil is ejected. 

NOTE: For some low-viscosity samples, the VersaTips may remain in the fill cups until after 

the sample scan has been completed. 

 

Summary of Contents for OilExpress 4

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands