1081
MCU Mode:
Program
Number
Program Name/Description
Input Data
Default
10-03-03
ETU Setup
– Number of Voice Channels
Read only program showing number of VoIP
resources available for voice calls.
This information can also be viewed by
pressing 4 on an idle display terminal.
11-19-01
Remote Conference Group Pilot Number
Enter the pilot number for remote conference.
Must work within current system
dialing plan.
No Setting
15-05-43
IP Telephone Terminal Basic Data Setup
–
Video Mode
Enable/Disable Video Mode for Standard SIP
terminals.
0 = Disable
1 = Enable
0
15-05-50
IP Telephone Terminal Basic Data Setup
–
Peer to Peer Mode
On a per station basis enable or disable Peer to
Peer mode.
If enabled, MUC mode resource settings are
used in Programs 84-27-22 and 84-27-23.
0 = Disable
1 = Enable
1
20-34-01
Remote Conference Group Setting
–
Remote Conference - Name
Set name for remote conference.
Maximum of 12 characters.
Conferences
1 ~ 4 =
Conf 1 - Conf 4
Conferences
5 ~ 20 = blank
20-34-02
Remote Conference Group Setting
–
Remote Conference - Password
Set password for remote conference.
Maximum of 4 numbers.
Conferences
1 ~ 4 = 1111
Conferences
5 ~ 20 = blank
20-34-06
Remote Conference Group Setting
–
Remote Conference - Password Mode
Set whether users are prompted to enter a
password to access the conference. Normal will
prompt users to enter a password. If set to Skip
no password is required to enter a conference.
0 = Normal
1 = Skip
0
20-34-07
Remote Conference Group Setting
– MCU
Mode for Remote Conference
Set the MCU video mode for remote
conference.
Setting this value for mode 1 or 2 determines
whether 84-27-22 or 84-27-23 is used.
0 = Disable
1 = Mode 1
2 = Mode 2
0
Summary of Contents for Univerge SV9100
