2-38
Service Manual
7558-
xxx
Go Back
Previous
Next
910.05
Service data error
Data communication error
Firmware upgrade is needed.
Go to
“910.02–910.07 Data
communication error” on page 2-266
.
910.06
Service data error
Data communication error
Firmware upgrade is needed.
Go to
“910.02–910.07 Data
communication error” on page 2-266
.
910.07
Service data error
Data communication error
Firmware upgrade is needed.
Go to
“910.02–910.07 Data
communication error” on page 2-266
.
940.02
Service data error
Clock signal communication error
The clock signal failed to reach the upper
printer PCBA.
Go to
“940.02 Clock signal
communication error” on page 2-267
.
940.03
Service data error
Controller communication failure
A software control-related error has
occurred.
Go to
“940.03 Controller communication
failure” on page 2-267
.
939.00
Service RIP engine
Comm.
RIP card assembly communication
failure
A communication error occurred between
the printer engine card and the RIP card
assembly.
Go to
“939.00 RIP card assembly
communication failure” on page 2-266
.
940.04
Service data error
IM logic failure
A software control-related error has
occurred.
Go to
“940.04 IM logic failure” on
page 2-268
.
951.xx
Service NVRAM
failure
RIP card assembly NVRAM failure
A failure has occurred in the RIP card
assembly NVRAM.
Go to
“951.xx RIP card assembly
NVRAM failure” on page 2-268
.
953.xx
Service NVRAM
failure
Operator panel assembly NVRAM
failure
NVRAM chip failure with operator panel
assembly (mirror).
Go to
“953.xx Operator panel assembly
NVRAM failure” on page 2-268
.
955.xx
Service Code CRC
error
RIP card assembly NAND CRC failure
The code ROM or NAND flash failed the
cyclic redundancy check.
Go to
“955.xx RIP card assembly NAND
CRC failure” on page 2-268
.
956.00
Service system board
error
RIP card assembly processor failure
The RIP card processor has failed.
Go to
“956.00 RIP card assembly
processor failure” on page 2-269
.
956.01
Service system board
error
RIP card assembly processor over
temperature failure
The RIP card assembly has exceeded safe
operating temperature.
Go to
“956.01 RIP card assembly
processor over temperature failure” on
page 2-269
.
9xx service error codes
Error code
Description
Action
Summary of Contents for X95 series
