HPC MOBILAIR M27 PE Operating Manual Download Page 233

Page: 233 / 312

1. Check compressed air options with condensate separation.
2. Drain and collect any residual quantities of condensate.

Dispose of any residual quantities of condensate and contaminated working materials in ac‐

cordance with applicable environmental protection regulations.

12.4.4 Removing filters/filter elements

Material Cleaning cloth

Receptacle

1. Remove all filters/filter elements from the machine.

Designation

Engine

Compressor

Filters/filter elements

Oil filter

Engine oil separator element

Oil separator cartridge

Filter/filter element,

fuel prefilter

—

Fuel filter

—

Filter/filter element,

fuel/water separator

—

Tab. 104 Machine filters/filter elements

2. Remove all filters/filter elements from the options specified on the machine.

Designation

Filter combination option

Fresh air filter option

Filters/filter elements

Prefilter

Adsorption filter element

Fine filter

High-performance filter element

Tab. 105 Machine option filters/filter elements

Dispose of working materials and components contaminated with operating fluids in accord‐

ance with applicable environmental protection regulations.

12.4.5 Disposing of the machine

Precondition All batteries have been removed and delivered to the designated disposal system.

All operating fluids have been drained and disposed of in accordance with applicable environmen‐

tal regulations.
Any residual quantities of condensate have been drained and disposed of in accordance with appli‐

cable environmental regulations.
All used filters/filter elements have been removed and disposed of in accordance with applicable

environmental regulations.

➤ Deliver the machine to an authorised disposal agent.

12 Decommissioning, Storage and Transport

12.4 Disposal

No.: 9_9548 22 HCE

Operating Manual Portable Rotary Screw Compressor
MOBILAIR M27 PE

221

Summary of Contents for MOBILAIR M27 PE

























































































































































































































































































































Search results

Summary of Contents for MOBILAIR M27 PE

Reviews:

Related manuals for MOBILAIR M27 PE

Brands by name

Popular brands

HPC MOBILAIR M27 PE, Operating Manual

Search results

Summary of Contents for MOBILAIR M27 PE

Reviews:

Related manuals for MOBILAIR M27 PE

Brands by name

Popular brands