HP P2000 G3 Cli Reference Manual Download

Page: 423 / 532

HP P2000 G3 MSA System CLI Reference Guide 423

job-parameters

Properties

Example

# show job-parameters

...

<PROPERTY name="background-scrub" type="string">Disabled</PROPERTY>

<PROPERTY name="background-scrub-pool" type="string">Disabled</PROPERTY>

<PROPERTY name="partner-firmware-upgrade" type="string">Disabled</PROPERTY>

Table 45

job-parameters properties

Name

Type

Description

background-

scrub

string

Shows whether disks in vdisks are automatically checked for disk defects to

ensure system health. The interval between background vdisk scrub finishing and

starting again is 24 hours.

•

Disabled

: Background vdisk scrub is disabled.

•

Enabled

: Background vdisk scrub is enabled. This is the default.

background-

scrub-numeric

string

Numeric equivalents for

background-scrub

values.

•

0: Disabled

•

1: Enabled

background-

scrub-pool

string

Not applicable.

background-

scrub-pool-

numeric

string

Not applicable.

partner-

firmware-

upgrade

string

Shows whether component firmware versions are monitored and will be

automatically updated on the partner controller.

•

Disabled

: Partner firmware upgrade is disabled.

•

Enabled

: Partner firmware upgrade is enabled. This is the default.

partner-

firmware-

upgrade-numeric

string

Numeric equivalents for

partner-firmware-upgrade

values.

•

0: Disabled

•

1: Enabled

utility-

priority

string

Priority at which data-redundancy utilities, such as vdisk verify and reconstruct,

run with respect to I/O operations competing for the system’s processors. (This

does not affect vdisk background scrub, which always runs at “background”

priority.)

•

High

: Utilities have higher priority than host I/O. Use when your highest

priority is to return the system to a fully fault-tolerant state. This can cause

heavy I/O to be slower than normal. This is the default.

•

Medium

: Utility performance is balanced with host I/O performance.

•

Low

: Utilities run at a slower rate with minimal effect on host I/O. Use when

streaming data without interruption, such as for a web server, is more

important than data redundancy.

utility-

priority-

numeric

string

Numeric equivalents for

utility-priority

values.

•

0: High

•

1: Medium

•

2: Low

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for P2000 G3

Reviews:

Related manuals for P2000 G3

Brands by name

Popular brands

HP P2000 G3, Cli Reference Manual

Search results

Summary of Contents for P2000 G3

Reviews:

Related manuals for P2000 G3

Brands by name

Popular brands