HP P2000 G3 Cli Reference Manual Download Page 461

Page: 461 / 532

HP P2000 G3 MSA System CLI Reference Guide 461

Example

# show expander-status

...

<PROPERTY name="type" type="string">Drive</PROPERTY>

<PROPERTY name="status" type="string">Enabled - Healthy</PROPERTY>

<PROPERTY name="elem-disabled" type="string">Enabled</PROPERTY>

elem-reason-

numeric

string

Numeric equivalents for

elem-reason

values.

•

(blank)

•

32769: Error count interrupts

•

32770: Externally disabled

•

32771: PHY control

•

32772: Not ready

•

32774: Drive removed

•

32775: Unused - disabled by default

•

32776: Excessive PHY changes

change-counter

uint32

Number of times the PHY originated a BROADCAST (CHANGE). A

BROADCAST (CHANGE) is sent if doubleword synchronization is lost or at the

end of a Link Reset sequence.

code-violations

uint32

Number of times the PHY received an unrecognized or unexpected signal.

disparity-

errors

uint32

Number of doublewords containing running disparity errors that have been

received by the PHY, not including those received during Link Reset sequences. A

running disparity error occurs when positive and negative values in a signal

don’t alternate.

crc-errors

uint32

In a sequence of SAS transfers (frames), the data is protected by a cyclic

redundancy check (CRC) value. The

crc-errors

value specifies the number of

times the computed CRC does not match the CRC stored in the frame, which

indicates that the frame might have been corrupted in transit.

conn-crc-errors

uint32

Number of times the lane between two expanders experienced a

communication error.

lost-dwords

uint32

Number of times the PHY has lost doubleword synchronization and restarted the

Link Reset sequence.

invalid-dwords

uint32

Number of invalid doublewords that have been received by the PHY, not

including those received during Link Reset sequences.

reset-error-

counter

uint32

Number of times the expander performed a reset of error counters.

flag-bits

uint32

PHY status flag bits.

Table 67

sas-status-controller-a properties (continued)

Name

Type

Description

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for P2000 G3

Reviews:

Brands by name

Popular brands

HP P2000 G3, Cli Reference Manual

Search results

Summary of Contents for P2000 G3

Reviews:

Brands by name

Popular brands