HP P2000 G3 Cli Reference Manual Download | Manualshive

Page: 162 / 532

background image

162 Alphabetical list of commands

set network-parameters

Description

Sets parameters for controller module network ports.
You can manually set static IP values for each controller, or you can specify that IP values should be

set automatically for both controllers through communication with a Dynamic Host Configuration

Protocol (DHCP) server.
Each controller has the following factory-default IP settings:

•

DHCP: enabled

•

Controller A IP address: 10.0.0.2

•

Controller B IP address: 10.0.0.3

•

IP subnet mask: 255.255.255.0

•

Gateway IP address: 10.0.0.1

When DHCP is enabled, the following initial values are set and remain set until the system is able to

contact a DHCP server for new addresses.

•

Controller A IP address: 10.0.0.2

•

Controller B IP address: 10.0.0.3

•

IP subnet mask: 255.255.255.0

•

Gateway IP address: 0.0.0.0

To switch a controller from DHCP addressing to static addressing, you must set the IP address,

netmask, and gateway values.
You can also set link speed, auto-negotiation, and duplex-mode parameters to enable Ethernet

switches to communicate with the storage system. These settings will persist if the Ethernet cable is

disconnected and reconnected, but will revert to default values if the controller is removed from the

enclosure. These settings affect only the network port of the controller on which this command is

entered.

Syntax

set network-parameters

[dhcp]

[ip

address

]

[netmask

netmask

]

[gateway

gateway

]

[controller a|b]

[ping-broadcast enabled|disabled|on|off]

[link-speed 10mbps|100mbps]

[duplex-mode full|half]

[auto-negotiation enabled|disabled|on|off]

[prompt yes|no]

[noprompt]

Parameters

dhcp

Optional. Specifies to use DHCP to set both controllers’ IP values.

ip

address

Optional. An IP address for the port.

netmask

netmask

Optional. An IP subnet mask for the port.

gateway

gateway

Optional. A gateway IP address for the port.

«
...
160
161
162
163
164
...
»

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P2000 G3

Brand: HAFNER Pages: 4

Brand: Graco Pages: 2

Wi-Fi USB Connector

Brand: Nintendo Pages: 3

Brand: Oasis Pages: 3

Brand: FasTest Pages: 3

L-force EYP A Series

Brand: Lenze Pages: 8

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

QUAD SHIELD SDW5162GN

Brand: Philips Pages: 2

Line Cord SWL6125

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Siemens Pages: 19

HELIAX FiberFeed HFA208 Series

Brand: CommScope Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands