manualshive.com logo in svg

HP P2000 G3, Cli Reference Manual

Share
Download
HP P2000 G3 Cli Reference Manual Download Page 346

346 XML API basetype properties

advanced-settings-table

Properties

Table 9

advanced-settings-table properties

Name

Type

Description

background-

scrub

string

Shows whether disks in vdisks are automatically checked for disk defects to 

ensure system health. The interval between background vdisk scrub finishing and 

starting again is specified by the 

background-scrub-interval

 parameter.

•

Disabled

: Background vdisk scrub is disabled.

•

Enabled

: Background vdisk scrub is enabled. This is the default.

background-

scrub-numeric

string

Numeric equivalents for 

background-scrub

 values.

•

0: Disabled

•

1: Enabled

background-

scrub-interval

uint16

Shows the interval in hours between background vdisk scrub finishing and 

starting again, from 1–360 hours. The default is 24 hours.

partner-

firmware-

upgrade

string

Shows whether component firmware versions are monitored and will be 

automatically updated on the partner controller.

•

Disabled

: Partner firmware upgrade is disabled.

•

Enabled

: Partner firmware upgrade is enabled. This is the default.

partner-

firmware-

upgrade-numeric

string

Numeric equivalents for 

partner-firmware-upgrade

 values.

•

0: Disabled

•

1: Enabled

utility-

priority

string

Priority at which data-redundancy utilities, such as vdisk verify and reconstruct, 

run with respect to I/O operations competing for the system's processors. (This 

does not affect vdisk background scrub, which always runs at “background” 

priority.)

•

High

: Utilities have higher priority than host I/O. Use when your highest 

priority is to return the system to a fully fault-tolerant state. This can cause 

heavy I/O to be slower than normal. This is the default.

•

Medium

: Utility performance is balanced with host I/O performance.

•

Low

: Utilities run at a slower rate with minimal effect on host I/O. Use when 

streaming data without interruption, such as for a web server, is more 

important than data redundancy.

utility-

priority-

numeric

string

Numeric equivalents for 

utility-priority

 values.

•

0: High

•

1: Medium

•

2: Low

smart

string

Shows whether SMART (Self-Monitoring Analysis and Reporting Technology) is 

enabled or disabled for disks.

•

Detect-Only

: Each disk in the system retains its individual SMART setting, 

as will new disks added to the system.

•

Enabled

: SMART is enabled for all disks in the system and will be enabled 

for new disks added to the system. This is the default.

•

Disabled

: SMART is disabled for all disks in the system and will be 

disabled for new disks added to the system.

smart-numeric

string

Numeric equivalents for 

smart

 values.

•

0: Detect-Only

•

1: Enabled

•

2: Disabled

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands