manualshive.com logo in svg

HP P2000 G3, Cli Reference Manual

Share
Download
HP P2000 G3 Cli Reference Manual Download Page 135

HP P2000 G3 MSA System CLI Reference Guide 135

partner-firmware-upgrade enabled|disabled|on|off

Optional. Sets whether component firmware versions are monitored and will be automatically 

updated on the partner controller.

•

disabled

 or 

off

: Partner firmware upgrade is disabled.

•

enabled

 or 

on

: Partner firmware upgrade is enabled. This is the default.

partner-notify enabled|disabled|on|off

Optional. Sets whether to notify the partner controller that a trigger condition occurred. Enable this 

option to have the partner also change to write-through mode for better data protection. Disable this 

option to allow the partner continue using its current caching mode for better performance. The 

default is 

disabled

.

•

disabled

 or 

off

: Notification is disabled. This is the default.

•

enabled

 or 

on

: Notification is enabled.

power-supply-failure enabled|disabled|on|off

Optional. Sets whether the cache policy automatically changes to write-through when a power 

supply fails.

•

disabled

 or 

off

: The power-supply failure trigger is disabled. This is the default.

•

enabled

 or 

on

: The power-supply failure trigger is enabled.

smart enabled|disabled|on|off|detect-only

Optional. Enables or disables SMART (Self-Monitoring Analysis and Reporting Technology) 

monitoring for all disks in the storage system.

•

disabled

 or 

off

: Disables SMART for all disks in the system and for all disks added to the 

system.

•

enabled

 or 

on

: Enables SMART for all disks in the system and for all disks added to the system. 

This is the default.

•

detect-only

: Detects but does not change the SMART setting of each disk in the system, and 

for each new disk added to the system.

super-cap-failure enabled|disabled|on|off

Optional. Sets whether the cache policy will change from write-back to write-through when the 

super-capacitor that provides backup power for cache is not fully charged or fails.

•

disabled

 or 

off

: The super-capacitor failure trigger is disabled.

•

enabled

 or 

on

: The super-capacitor failure trigger is enabled. This is the default.

sync-cache-mode immediate|flush

Optional. Sets how the 

SCSI SYNCHRONIZE CACHE

 command is handled. 

•

immediate

: Good status is returned immediately and cache content is unchanged. This option 

is the default. 

•

flush

: Good status is returned only after all write-back data for the specified volume is flushed 

to disk.

temperature-exceeded enabled|disabled|on|off

Optional. Sets whether the system will shut down a controller when its temperature exceeds the 

critical operating range.

•

disabled

 or 

off

: The over-temperature trigger is disabled. This is the default.

•

enabled

 or 

on

: The over-temperature trigger is enabled.

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands