manualshive.com logo in svg

HP P2000 G3, Cli Reference Manual

Share
Download
HP P2000 G3 Cli Reference Manual Download Page 167

HP P2000 G3 MSA System CLI Reference Guide 167

set priorities

Description

Sets snapshot-retention priorities for a specified snap pool. Snap-pool priorities, in conjunction with 

snapshot priorities, determine which snapshots are retained if system resource limitations require 

some snapshots to be automatically deleted. 
Lower-priority snapshots will be deleted before higher-priority snapshots. Priority values are 

1–65535. To use a default priority, specify the value 0.

Syntax

set priorities 

[standard-snap 

#

]

[volume-copy 

#

]

[replication-snap 

#

]

[replicating 

#

]

[common-sync-point 

#

]

[only-sync-point 

#

]

[queued 

#

]

snap-pool

Parameters

standard-snap 

#

Optional. Retention priority for a standard snapshot. The default is 0x6000 (24576).

volume-copy 

#

Optional. Retention priority for a snapshot that is being used to copy data from a source volume to a 

destination volume. This attribute is temporary for the duration of the volume-copy process. The 

default is 0xa000 (40960).

replication-snap 

#

Optional. Retention priority for a replication snapshot. The default is 0x4000 (16384).

replicating 

#

Optional. Retention priority for a snapshot that is being replicated to a secondary volume. This 

snapshot is required in order to resume the replication. The attribute is temporary for the duration of 

the replication process. The default is 0xc000 (49152).

common-sync-point 

#

Optional. Retention priority for the latest snapshot that is copy complete on all secondary volumes. It 

identifies a common point in time that is known by all destinations. The default is 0x8000 (32768).

only-sync-point 

#

Optional. Retention priority for the only sync point that is available on at least one secondary 

volume. If this snapshot is removed, then the next replication requires a full sync to be performed. The 

default is 0xe000 (57344).

queued 

#

Optional. Retention priority for a snapshot that was taken for remote replication but is queued 

waiting for the previous replications to complete. The default is 0x2000 (8192).

snap-pool

Name or serial number of the snap pool.

Example

Set attribute priorities for snap pool 

SP1

, raising the priority for standard snapshots and leaving 

other priorities unchanged:

# set priorities only-sync-point 65535 SP1

Success: Command completed successfully. - The priorities were successfully set. 
(2012-01-21 12:28:24)

See also

•

show priorities

•

show snap-pools

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands