HP P2000 G3 Cli Reference Manual Download Page 503

Page: 503 / 532

HP P2000 G3 MSA System CLI Reference Guide 503

largest-free-

partition-

space-numeric

string

Unformatted

largest-free-partition-space

value in 512-byte blocks.

num-drives-per-

low-level-array

uint8

•

For a RAID-10 or RAID-50 vdisk, the number of disks in each sub-vdisk.

•

For other RAID levels,

num-expansion-

partitions

uint8

Not used.

num-partition-

segments

uint8

Number of free segments available for expansion of volumes.

new-partition-

lba

string

Maximum number of 512-byte blocks that could be allocated to a newly created

volume. The value is formatted to use the current base, precision, and units.

Expanding a volume in the same vdisk will reduce this amount.

new-partition-

lba-numeric

string

Unformatted

new-partition-lba

value in 512-byte blocks.

array-drive-

type

string

Type of disk used in the vdisk.

•

SAS

: Dual-port SAS.

•

SAS-S

: Single-port SAS.

•

SATA

: Dual-port SATA.

•

SATA-S

: Single-port SATA.

array-drive-

type-numeric

string

Numeric equivalents for

array-drive-type

values.

•

3: SATA

•

4: SAS

•

5: SATA-S

•

6: SAS-S

is-job-auto-

abortable

string

•

false

: The current job must be manually aborted before you can delete the

vdisk.

•

true

: The current job will automatically abort if you delete the vdisk.

is-job-auto-

abortable-

numeric

string

•

0: false

•

1: true

serial-number

string

Vdisk serial number.

blocks

uint64

Unformatted

size

value in 512-byte blocks.

disk-dsd-

enable-vdisk

string

•

Disabled

: DSD is disabled for the vdisk. This is the default.

•

Enabled - all spinning

: DSD is enabled for the vdisk.

•

Partial spin-down

: DSD is enabled for the vdisk and its disks are

partially spun down to conserve power.

•

Full spin-down

: DSD is enabled for the vdisk and its disks are fully spun

down to conserve power.

disk-dsd-

enable-vdisk-

numeric

string

•

0: Disabled

•

1: Enabled - all spinning

•

2: Partial spin-down

•

3: Full spin-down

disk-dsd-delay-

vdisk

uint32

The period of inactivity after which the vdisk's disks and dedicated spares

automatically spin down, from 1–360 minutes. DSD is enabled by a value in this

range, or is disabled by the value 0.

total-data-

transferred

bytes

Total amount of data read and written since the last sampling time.

Table 90

virtual-disks properties (continued)

Name

Type

Description

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for P2000 G3

Reviews:

Brands by name

Popular brands

HP P2000 G3, Cli Reference Manual

Search results

Summary of Contents for P2000 G3

Reviews:

Brands by name

Popular brands