manualshive.com logo in svg

HP P2000 G3, Cli Reference Manual

Share
Download
HP P2000 G3 Cli Reference Manual Download Page 52

52

Alphabetical list of commands

create replication-set

Description

Creates a replication set from a specified standard or master volume. If you specify a standard 

volume, it is converted to a master volume using default policies for snap-pool creation. You can 

optionally use the 

reserve

 parameter to set the snap-pool size. The specified volume becomes the 

replication set's primary volume.
You can specify a remote volume to be the replication set's secondary volume, or one will be 

created. When a 

replicate snapshot

 or 

replicate volume

 command is issued, data in the primary 

volume is replicated to the associated secondary volume. 
You can associate the primary volume with a remote system in two ways:

•

If the local and remote MCs can communicate, you can specify a vdisk on a remote system. A 

master volume and snap-pool are created in the remote vdisk.

•

If the local and remote MCs cannot communicate or you want to use an existing 

replication-prepared volume on the remote system, you can specify the volume to use as the 

secondary volume. 

You can also start the initial replication by specifying the 

snapshot

 parameter.

If you create a replication set without specifying a replication destination, a partial set is created and 

you must use the 

add replication-volume

 command to complete the set before you can perform 

replication.

IMPORTANT:

Before starting this procedure, if you intend to use CHAP to authenticate iSCSI login 

requests between the local system and a remote system, do the following:

•

Create a one-way CHAP record on each system. On the local system, the CHAP record must refer 

to the node name of the remote system. On the remote system, the CHAP record must refer to the 

node name of the local system. Both records must use the same secret. (Mutual CHAP is not used 

between storage systems. CHAP records' mutual fields can be set but are not used.) To create a 

CHAP record, use the 

create chap-record

 command.

•

After the CHAP records are created, enable CHAP on the primary system, the secondary system, 

or both. To enable CHAP, use the 

set iscsi-parameters

 command.

If both records don't exist or don't use the same secret, replication-set creation will fail.

If the create transaction fails, a prompt asks if you want to revert the transaction, which undoes any 

changes made in attempting to create the replication set. To revert, enter 

yes

; otherwise, enter 

no

.

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands