HP P2000 G3 Cli Reference Manual Download | Manualshive

Page: 334 / 532

background image

334 Alphabetical list of commands

State

•

AVAIL

: Available.

•

FAILED

: The disk is unusable. Reasons for this status include: excessive media errors; SMART

error; disk hardware failure; unsupported disk.

•

GLOBAL SP

: Global spare.

•

LEFTOVR

: Leftover.

•

VDISK

: Used in a vdisk.

•

VDISK SP

: Spare assigned to a vdisk.

Partially Reconstructed

•

True

: The disk contains partially reconstructed data.

•

False

: The disk does not contain partially reconstructed data.

Out Of Sync

•

True

: The disk data is out of sync with other disks in the vdisk.

•

False

: The disk data is in sync with other disks in the vdisk.

Age

The age of the disk in the vdisk. The age value starts at 1 and is incremented for all good disks in the

vdisk each time there is a change in the disk configuration of the vdisk, such as when a disk is

detected to have failed or be missing. Therefore, if a disk has a lower age than other disks in the

vdisk, that disk is out-of-sync with the other vdisk members. This value can be used as a guide to

decide which disks to physically remove before doing the trust operation to minimize the amount of

corrupt data in the trusted vdisk if you want to use the

unsafe

parameter.

Example

Trust a vdisk which has enough good disks to complete the trust operation. The vdisk may have

out-of-sync or partially reconstructed disks but they are not needed to complete the trust operation.

The command completes successfully.

# trust enable

Success: Command completed successfully. - Trust is enabled. (2013-09-17
04:29:28)

# trust vdisk VD1

Success: Command completed successfully. (VD1) - Trust operation completed
successfully for this vdisk. (2013-09-17 04:29:35)

Trust a vdiskwhich does not have enough good disks available to complete the trust operation. The

command fails.

# trust enable

Success: Command completed successfully. - Trust is enabled. (2013-09-17
04:12:49)

# trust vdisk VD1

Error: The trust operation failed because the vdisk has an insufficient number
of in-sync disks. - Please contact Support for further assistance.
(2013-09-17 04:13:13)

Trust a vdisk which has out-of-sync or partially reconstructed disks that would be needed to complete

the trust operation. The command fails.

# trust enable

Success: Command completed successfully. - Trust is enabled. (2013-09-17
09:06:41)

# trust vdisk VD1

Error: Command failed. - The vdisk specified contains out-of-sync or partially
reconstructed disks that are necessary to restore the vdisk to an accessible
state. Continuing with the trust operation may lead to data corruption. Please
contact Support for further assistance. (2013-09-08 09:06:46)

«
...
332
333
334
335
336
...
»

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P2000 G3

Brand: AAVARA Pages: 8

Brand: NAiS Pages: 4

Brand: Paradyne Pages: 12

Brand: Panduit Pages: 5

Brand: MiLAN Pages: 10

Brand: Scheppach Pages: 100

Brand: Covid Pages: 7

PowerCon NAC3MPA

Brand: NEUTRIK Pages: 2

Brand: Hama Pages: 26

Brand: Kinivo Pages: 10

Brand: VivoLink Pages: 18

Brand: RocketFish Pages: 2

Brand: Chauvet Professional Pages: 117

Brand: SIIG Pages: 8

Brand: EUCHNER Pages: 10

Brand: 3M Pages: 16

Brand: nvent Pages: 6

Raychem HAK-C-100

Brand: nvent Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands