HP P2000 G3 Cli Reference Manual Download Page 253

Page: 253 / 532

HP P2000 G3 MSA System CLI Reference Guide 253

show network-parameters

Description

Shows the settings and health of each controller module’s network port.

Syntax

show network-parameters

Output

IP Address

Network port IP address.

Gateway

Network port gateway IP address.

Subnet Mask

Network port IP subnet mask.

MAC Address

Controller’s unique Media Access Control address.

Addressing Mode

•

Manual

: Network settings set manually (statically).

•

DHCP

: DHCP used to set network parameters.

Link Speed

•

Unknown

: Either the link speed has not been set, or it has been unset because the controller

module was removed from its enclosure.

•

10mbps

: The network port link speed is set to 10 Mb/s.

•

100mbps

: The network port link speed is set to 100 Mb/s.

Duplex Mode

•

Undefined

: Either the duplex mode has not been set, or it has been unset because the

controller module was removed from its enclosure.

•

Half

: The network port duplex mode is set to half duplex.

•

Full

: The network port duplex mode is set to full duplex.

Auto Negotiation

•

Disabled

: Either the network port has not been set, or it has been unset because the controller

module was removed from its enclosure, or the port is connected to a switch and is set to use the

link speed and duplex mode shown by the

Link Speed

and

Duplex Mode

fields.

•

Enabled

: The network port is set to auto-negotiate a link speed (up to the maximum speed

shown by the

Link Speed

field) and duplex mode with a connected Ethernet switch.

Health

The health of the network connection.

•

Degraded

Health Reason

If Health is not

, this field shows the reason for the health state.

Health Recommendation

If Health is not

, this field shows recommended actions to take to resolve the health issue.

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for P2000 G3

Reviews:

Brands by name

Popular brands

HP P2000 G3, Cli Reference Manual

Search results

Summary of Contents for P2000 G3

Reviews:

Brands by name

Popular brands