HP P2000 G3 Cli Reference Manual Download Page 69

Page: 69 / 532

HP P2000 G3 MSA System CLI Reference Guide

create volume

Description

Creates a volume in a vdisk. You must specify a size for the volume. You can create the volume

unmapped or set its default mapping. Default mapping settings apply to all hosts, unless overridden

by an explicit mapping between a host and the volume. You can later change the mapping by using

the

map volume

and

unmap volume

commands.

By default, this command will not map the created volume.

Syntax

create volume

vdisk

vdisk

size

size

[B|KB|MB|GB|TB|KiB|MiB|GiB|TiB]

[mapping

ports

LUN

]

[access read-write|rw|read-only|ro|no-access]

[lun

LUN

]

[ports

ports

]

[snap-pool

snap-pool

]

[reserve

size

[B|KB|MB|GB|TB|KiB|MiB|GiB|TiB]]

[snappable]

[prepare-replication-volume]

[ovms-uid

]

name

Parameters

vdisk

vdisk

Name or serial number of the vdisk to create the volume in. For vdisk syntax, see

Command syntax

on page 22.

size

size

[B|KB|MB|GB|TB|KiB|MiB|GiB|TiB]

Sets the volume size using the current base, as shown by the

show cli-parameters

command. The unit

can be specified as follows:

•

If base 2 is in use:

(bytes),

KiB

(kibibytes),

MiB

(mebibytes), or

GiB

(gibibytes).

•

If base 10 is in use:

(bytes),

(kilobytes),

(megabytes), or

(gigabytes).

If no unit is specified, the unit is 512-byte blocks.

mapping

ports

LUN

Deprecated; use the

ports

and

lun

parameters.

access read-write|rw|read-only|ro|no-access

Optional. The access permission for hosts connected to the controller for this volume: read-write (

read-only (

), or no-access. If

no-access

is specified, the volume is not mapped. The default is

read-write

lun

LUN

Optional if the access parameter is set to

no-access

. Specifies the LUN to assign to the mapping

on all ports.

ports

ports

Optional. The ports through which the host can access the volume. In a combo system, select either

FC or iSCSI ports, not both. For port syntax, see

Command syntax

on page 22. If this parameter is

omitted, all ports are selected.

snap-pool

snap-pool

Optional. Name or serial number of the snap pool to associate with the new volume. For volume

syntax, see

Command syntax

on page 22.

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for P2000 G3

Reviews:

Brands by name

Popular brands

HP P2000 G3, Cli Reference Manual

Search results

Summary of Contents for P2000 G3

Reviews:

Brands by name

Popular brands