HP P2000 G3 Cli Reference Manual Download | Manualshive

Page: 49 / 532

background image

HP P2000 G3 MSA System CLI Reference Guide

49

create master-volume

Description

Creates a volume that is enabled for snapshots. The master volume is created in a specified vdisk

and is associated with a specified snap pool. You can either associate the master volume with an

existing snap pool owned by the same controller, or optionally specify the size of a new snap pool to

automatically create. The vdisk and snap pool must be owned by the same controller.
For use with remote replication, you can create a replication-prepared volume that is intended to be

added to a replication set as its secondary volume. A secondary volume cannot be assigned a LUN

or mapped to hosts.

Syntax

create master-volume

vdisk

vdisk

size

size

[B|KB|MB|GB|TB|KiB|MiB|GiB|TiB]

[snap-pool

snap-pool

]

[reserve size[B|KB|MB|GB|TB|KiB|MiB|GiB|TiB]]

[lun

LUN

]

[prepare-replication-volume]

[ovms-uid

ID

]

name

Parameters

vdisk

vdisk

Name or serial number of the vdisk to create the volume in. For vdisk syntax, see

Command syntax

on page 22.

size

size

[B|KB|MB|GB|TB|KiB|MiB|GiB|TiB]

Sets the volume size using the current base, as shown by the

show cli-parameters

command. The unit

can be specified as follows:

•

If base 2 is in use:

B

(bytes),

KiB

(kibibytes),

MiB

(mebibytes), or

GiB

(gibibytes).

•

If base 10 is in use:

B

(bytes),

KB

(kilobytes),

MB

(megabytes), or

GB

(gigabytes).

If no unit is specified, the unit is 512-byte blocks.

snap-pool

snap-pool

Optional. Name or serial number of the snap pool to associate with the new master volume. For

volume syntax, see

Command syntax

on page 22. If this parameter is omitted, the system

automatically creates a snap pool that is either 20% of the master volume's size or 5.37 GB,

whichever is larger. Use either this parameter or the

reserve

parameter.

reserve

size

[B|KB|MB|GB|TB|KiB|MiB|GiB|TiB]

Optional. Size of the snap pool to create in the vdisk. The default size is either 20% of the volume

size or 5.37 GB, whichever is larger. Use either this parameter or the

snap-pool

parameter.

NOTE:

In rare cases, a large amount of I/O can cause a snap pool that is too small to fill quickly.

This can result in all snapshots being deleted due to the snap pool running out of space. Create snap

pools of at least 50 GB to avoid this situation.

lun

LUN

Optional. A default LUN to assign to the new master volume. If this parameter is omitted, no LUN is

assigned. Use either this parameter or the

prepare-replication-volume

parameter.

prepare-replication-volume

Optional. Specifies to create a replication volume instead of a regular master volume. Use either this

parameter or the

lun

parameter.

ovms-uid

ID

For a volume to be accessed by an OpenVMS host, assign a volume ID in the range 1–32767 to

identify the volume to the host.

«
...
47
48
49
50
51
...
»

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P2000 G3

Brand: IBM Pages: 28

FutureLink 649NV-48

Brand: Suttle Pages: 2

COMPONENT CABLE LUXURY COMPONENT CABLE FOR...

Brand: GAMERON Pages: 32

Brand: W Box Technologies Pages: 26

Brand: ELCART Pages: 2

Brand: Tripp Lite Pages: 2

Brand: Panduit Pages: 4

Brand: SeaLevel Pages: 34

Brand: Philips Pages: 2

opticalCON DRAGONFLY NKO2S-XP Series

Brand: NEUTRIK Pages: 4

Brand: Delphi Pages: 33

Brand: Delphi Pages: 41

Brand: Black Box Pages: 22

Brand: fios Pages: 8

Brand: Steren Pages: 2

Brand: VITELEC Pages: 4

Blackbird 36741

Brand: Monoprice Pages: 11

Brand: UTE Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands