HP P2000 G3 Cli Reference Manual Download

Page: 156 / 532

156 Alphabetical list of commands

gateway

address

Optional. For iSCSI, the port gateway address.

address

Optional. For iSCSI, the port IP address. Ensure that each iSCSI host port in the storage system is

assigned a different IP address.

iscsi-ip-version ipv4|ipv6

Specifies whether to use IP version 4 (IPv4) or 6 (IPv6) for addressing controller iSCSI ports.

•

ipv4

: Lets you specify addresses in dot-decimal format, where the four octets of the address use

decimal values without leading zeroes and the octets are separated by a period; for example,

10.132.2.205

. This option is the default.

•

ipv6

: Lets you specify addresses using eight groups of four hexadecimal digits, where the

groups are separated by a colon. All groups must be specified. For example,

0000:0000:0000:0000:0000:0000:0A90:3442.

netmask

address

Optional. For iSCSI, the port netmask address.

noprompt

Optional in console format; required for XML API format. Suppresses the confirmation prompt, which

requires a yes or no response. Specifying this parameter allows the command to proceed without

user interaction.

ports

ports

|all

Optional. Specific host port numbers or all ports. For port syntax, see

Command syntax

on page 22.

prompt yes|no|expert

Optional. Specifies an automatic response to the confirmation prompt:

•

yes

: Allow the command to proceed.

•

: Cancel the command.

•

expert

: Allow the command to proceed.

If this parameter is omitted, you must manually reply to the prompt.

speed 2g|4g|8g|auto

Optional. For FC, sets a forced link speed in Gbit/sec or lets the speed be auto-negotiated (

auto

Because a speed mismatch prevents communication between the port and host, set a speed only if

you need to force the port to use a known speed for testing, or you need to specify a mutually

supported speed for more than two FC devices connected in an arbitrated loop.

Example

On a system with FC ports, set the link speed to 8 Gbit/sec for ports A1 and B1:

# set host-parameters speed 8g ports a1,b1

WARNING: This change will take effect immediately. Changes may affect access to
data. Are you sure?

yes

Success: Command completed successfully. - The host parameters were changed
successfully. (2012-01-21 15:42:52)

On a system with FC ports, set controller A ports to request loop ID 14 and controller B ports to use

soft target addressing, and suppress the confirmation prompt:

# set host-parameters fibre-loop-id 14,soft noprompt

Info: Changes to FC loop IDs will not take effect until the affected Storage
Controller is rebooted.

Success: Command completed successfully. - The host parameters were changed
successfully. (2012-01-21 15:45:00)

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for P2000 G3

Reviews:

Related manuals for P2000 G3

Brands by name

Popular brands

HP P2000 G3, Cli Reference Manual

Search results

Summary of Contents for P2000 G3

Reviews:

Related manuals for P2000 G3

Brands by name

Popular brands