manualshive.com logo in svg

HP P2000 G3, Cli Reference Manual

Share
Download
HP P2000 G3 Cli Reference Manual Download Page 62

62

Alphabetical list of commands

Parameters

type TakeSnapshot|ResetSnapshot|VolumeCopy|ReplicateVolume|EnableDSD

|DisableDSD

The task type:

•

TakeSnapshot

: Takes a snapshot of a standard or master volume.

•

ResetSnapshot

: Deletes the data in the snapshot and resets it to the current data in the 

associated master volume. The snapshot's name and other volume characteristics are not 

changed.

•

VolumeCopy

: Copies a standard, master, or snapshot volume to a new standard volume. The 

command creates the destination volume you specify, which must be in a vdisk owned by the 

same controller as the source volume.

•

ReplicateVolume

: Replicates a replication set's primary volume to a remote system.

•

EnableDSD

: Enables spin down for all vdisks. You can use this to enable or resume spin down 

during hours of infrequent activity.

•

DisableDSD

: Disables spin down for all vdisks. You can use this to disable or suspend spin 

down during hours of frequent activity.

source-volume 

volume

For a 

TakeSnapshot

 task, the name or serial number of the standard or master volume to take a 

snapshot of. For a 

VolumeCopy

 task, the name or serial number of the standard, master, or 

snapshot volume to copy. For a 

ReplicateVolume

 task, the name or serial number of the primary 

volume to replicate. For volume syntax, see 

Command syntax

 on page 22.

snapshot-prefix 

prefix

A label to identify snapshots created by this task. Snapshot names have the format 

prefix

_s

#

, 

where 

#

 starts at 

001

.

retention-count 

#

For a 

TakeSnapshot

 task this parameter specifies the number of snapshots created by this task to 

retain, from 1 to the licensed limit. When a new snapshot exceeds this limit, the oldest snapshot with 

the same prefix is deleted.
For a 

ReplicateVolume

 task this parameter specifies the number of replication images created by 

this task to retain, from 2 to 32. When a new image exceeds this limit, the oldest image with the 

same prefix is deleted. This parameter applies to the primary volume only; for the secondary volume, 

images will accumulate until either the secondary vdisk's space limit is reached or the maximum 

number of images is reached, after which the oldest image will be deleted as new images are 

created.

snapshot-volume 

volume

Name or serial number of the snapshot to reset. For volume syntax, see 

Command syntax

 on 

page 22.

dest-vdisk 

vdisk

Name or serial number of the destination vdisk for the volume copy. For vdisk syntax, see 

Command 

syntax

 on page 22.

dest-prefix 

prefix

A label to identify the volume copy created by this task. Copy names have the format 

prefix

_c

#

, 

where 

#

 starts at 

001

.

modified-snapshot yes|no

Optional. Specifies whether to include or exclude modified write data from the snapshot in the copy. 

This parameter applies only when the source volume is a snapshot; it is ignored if the source volume 

is a master volume.

•

yes

: Include modified snapshot data.

•

no

: Exclude modified snapshot data.

If this parameter is omitted for a snapshot, modified snapshot data is excluded.

Summary of Contents for P2000 G3





















































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands