manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 99

92

Adjustment

1. Check and adjust clutch pedal height

The clutch pedal height should be 180~186 mm. Adjust the pedal by adjusting bolts.

2. Check and adjust clutch pedal stroke and free stroke

(1) The clutch pedal stroke: 134~142mm

(2)  The clutch pedal free stroke: 10~30 mm

If the clutch pedal stroke and free stroke are not within specification, adjust it by adjusting the location of

the adjusting nut on the clutch cable. Re-adjust the clutch pedal height if necessary.

3. Check that the clutch pedal operates in flexible and reliable way

Notice:

(1) Make sure the clutch is fully applied and completely released when control the clutch

pedal.

(2) The clutch pedal must have certain free stroke. Otherwise, the full application of the

clutch may be impacted

(3) Tighten the lock nut after adjustment

Connect The 

Clutch Cable

Bushing

Bushing

Adjusting Bolt

Brake Pedal Assembly 

Sleeve

 Clutch Pedal Torsion Spring  

Retainer 

Pedal Mat

Clutch Pedal Assembly

Clutch 
Pedal 
Bracket 
Assembly

Adjusting Nut

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands