manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 48

41

Chapter 4 Fuel System

(MR7131A, MR7151A, MR7161A)

Section 1 Check Fuel System Pressure

1. Remove the fuel tank from the vehicle

2. Check the fuel pump running

(a) Connect the positive and negative battery terminal to the concerned

fuel pump connector. See (Figure 91).

Notice: Do not start engine

The sound of fuel flowing can be heard if there is pressure.

Check fusible link, fuse, EFI open circuit relay, fuel pump, ECU and

wire connector if there is no pressure.

(b) Turn the ignition switch to "OFF" position.

3. Check fuel pressure

(a)  Check battery electrical pressure to be above 12V.

(b)  Detach negative terminal cable from the battery.

(c) Install pressure gage from the fuel delivery pipe. See (Figure 92).

(d) Connect battery negative terminal.

(e) Measure fuel pressure

Fuel pressure:

304-343kPa

Check fuel pipe & union, fuel pump, fuel filter if the pressure is too

low.

(f) Start engine. Measure fuel pressure at idle. Fuel pressure: 304-343kPa

(g) Check fuel pressure and retain the pressure for approximately 5min after the engine stopped.

Fuel pressure: 147kPa

Figure 91

Figure 92

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands