manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 344

337

(8) Make sure the warning light of the airbag system on for 6s and off.

If the warning light of the airbag system is not as specified, it means system fault. Check with the OBD (on-

board diagnostics).

4.Rear Seat Belt Removal / Installation

Warning

Do not remove retractor.

(1) Fold rear seat back.

(2) Remove B pillar upper inside trim.

(3) Remove rear trunk partition.

(4) Remove bolt.

(5) Remove rear seat belt.

(6) The installation is in the reverse order of the removal.

5.Rear Seat Belt Buckle Removal / Installation

(1)  Remove rear seat cushion.

(2) Remove the bolt.

(3) Remove rear seat belt buckle.

(4) The installation is in the reverse order of the removal.

6.  Seat Belt Inspection

(1) Ensure correct installation of seat belt.

(2) Check the metal component of the seat belt for damage.

(3) If the vehicle has been vibrated during the accident, pull out the

seat belt from the retractor, observe by eye and touch the seat

belt with hand to ensure that there is no scratch (load limit retractor

does not operate).

z

Replace the seat belt if it is not as specified in the technical specification.

Seat Belt

Pull

Anchor

Nick

anchorage

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands