Geely CK MR479Q 2007 Workshop Manual Download Page 342

Page: 342 / 392

335

(VII) Seat Belt

The vehicle seat belt is compulsory for drivers and passengers for safety purpose. It is the facility to prevent

the passengers from being hurt or reduce the possibility of being hurt when the vehicle is in emergent drive or

traffic accident occurs. Ck-1 front seat adopts Three Points Emergency Lock Retractor Pretension Seat

Belt , It is composed of retractor assembly, belt buckle assembly and height adjuster assembly.

1. Height Adjuster Assembly

2. Retractor Assembly

3. Belt Buckle Assembly 4.anchorage

1. Belt Buckle

Belt buckle is enclosure type, See Figure

Replacement Of The Seat Belt Buckle

(1) Remove the seat adjuster hinge cover;

(2) Remove the bolt from the belt buckle on the seat side;

(3) Remove the seat belt buckle from the seat;

(4) Replace the seat belt buckle.

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands