Geely CK MR479Q 2007 Workshop Manual Download Page 196

Page: 196 / 392

189

II. SPEEDOMETER INSPECTION

1. INSPECT THE INDICATING ERROR ALLOWED BY SPEEDOMETER USING A SPEEDOM-

ETER TESTER, AND INSPECT THE OPERATION OF THE ODOMETER.

NOTICE:

Tire over or under inflation will cause the reading error.

2. INSPECT INPUT SIGNAL

(a) Connect the positive (+) pole of the voltmeter to terminal A-11, and the negative (-) to the terminal A-9.

(b) When the vehicle runs at 10 Km/h, inspect the voltage between terminal A-11 and A-9 of the combination

meter.

Standard: 7 wave forms of the high-low electrical level change per second.

NOTICE:

Hold the ignition switch ON when inspected, connect the connector.

3. INSPECT TACHOMETER

Inspect its operation

(1) Start the engine, using a handy tachometer to compare.

(2) The value displayed on the handy tachometer and the value indicated on the tachometer are as follows.

Meter indication

Value displayed on the tester

17—23

35—40

55—60

75—80

100

95—100

120

114—120

140

133—140

160

152—160

180

171—180

Analog Meter (Km/h)

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands