manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 50

43

Section 3 Fuel Injector Replacement

1. Check fuel for ejection.

2. Remove PCV ventilation hoses. See (Figure 95). Remove fuel pipe clamp.

3. Detach fuel hose sub-assembly

4. Detach fuel delivery pipe sub-assembly. See (Figure 96)

(a) Press the connector to lock the spring and pull the connector from the injector.

(b) Remove 2 screws and detach fuel delivery pipe with injector.

5. Remove fuel injector assembly

6. Install injector assembly

(a) Smear a light layer of oil on two O-rings and install them to injector. See (Figure 97).

(b) Install 4 injectors to feul delivery pipe by rotating them left and right. See (Figure 98).

(c) Install retain frame to each injector.

Figure 95

Figure 96

Figure 97

Figure 98

New O-ring

Upward

Ratain Frame

Push

Rotate

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands