manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 127

120

4. Remove the left and right rear strut assembly

(1) Remove the threaded connect of the rear strut assembly and rear brake assembly

(2) Remove the 3 nuts attaching the rear suspension upper mount to the body

Caution: reliable object shall be used to support the rear brake assembly! Make sure that the

brake pipeline is not affected or damaged!

5. Disassembly the left, right rear strut assembly

(1)  Set the rear strut assembly with special tool. Remove the nut on the top of the

rear shock absorber piston

Caution: The spring may rebound!

(2) Remove the rear suspension upper mount, rear suspension upper mount cushion,

rear suspension spring upper insulator, rear suspension spring, rear shock absorber

cushion, rear shock absorber dust preventing sleeve, rear suspension spring lower insulator in order

6. The assembly is in the reverse order of the disassembly.

Caution:

(1) when installing the nut on the shock absorber piston rod upper end, use special fixture

and be careful that the spring may rebound!

Torque : 32~38N.m

(2) Rear strut assembly to body thread torque : 32~38 N.m

(3) Strut assembly to rear brake assembly thread torque : 81~96 N.m

(4) Install the ABS rear wheel sensor and the secure the signal wire

(5) When securing the brake line, make sure that the brake line does not interfere with

other parts

(6) Wheel nut torque : 95~115N.m

(7) Check the brake system for leakage, bleed air in the brake system as necessary

(8) Check whether the ABS signal is normal

(9) Check rear wheel alignment, adjust it as necessary

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands