Geely CK MR479Q 2007 Workshop Manual Download Page 295

Page: 295 / 392

288

6 No DTC output

（

can not

communicate with the scan meter

）

Likely Causes

[Description]

It may be the ABS ECU power

supply circuit or diagnosis wire circuit that can

not communicate with the scan meter

Burned fuse

Diagnosis wire broken or connector disconnected

Damaged ABS ECU

Scan meter faulty

Can the scan meter commu-

nicate with the MK-20 ABS

ECU on other vehicles?

ABS scan meter faulty, check it af-

ter repairing it

Replace

Check the power cable, ground wire

and diagnostic wire in the diagnos-

tic interface

Check the diagnostic interface or wire harness

Yes

Continuity

Check ABS power supply

fuse

Replace the ABS ECU

Repair the

diagnostic

interface or

harness

Is there any scan meter

Abn.

Remove the ABS ECU

connector, check whether

there is continuity between

terminal 7 in the ABS wire

harness and the terminal 8 in

the diagnostic interface

Abn.

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands