Geely CK MR479Q 2007 Workshop Manual Download Page 61

Page: 61 / 392

Section 2 Water Pump, Thermostat and Radiator Replacement

Hoist the engine from the compartment. See "Provison 20, Section 2, Chapter 2".

1. Replace water pump. See (Figure 125)

(1) Drain the coolant.

(2) Detach timing belt.

(3) Detach power steering pump assembly.

(4) Remove the oil dipstick guide.

(5) Detach water pump assembly.

(6) Install water pump assembly.

(7) The installation is in the reverse order of the removal.

2. Replace thermostat

(1) Remove thermostat (See Figure 126).

(2) Install thermostat.

a. Install a new gasket to the thermostat. See (Figure 127).

b.Align the main valve of the thermostat to the top of the

stud. Insert the thermostat into the water inlet case.

Hint:

The main valve is set at around 10°C as shown in the figure. See (Figure 128).

(3) Install inlet connector.

Figure 127

Figure 128

3. Replace radiator

(1) Open radiator cap.

(2) Open the drain valve and drain the coolant.

(3) Detach radiator water inlet hose.

(4) Detach radiator water outlet hose.

Figure 125

Figure 126

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands