Geely CK MR479Q 2007 Workshop Manual Download Page 241

Page: 241 / 392

234

Check the voltage between terminals under each operating condition as shown in the table below.

Abnormal:

Repair or replace wire harness and connector

Normal: Check and replace radio assembly

10. Power coming in, but CD player not operating.

(1) Press CD player "OPEN" to see if CD ejects.

No CD does not eject for inspection after being inserted

Yes Check if the right CD is inserted

(2) Check if the proper CD is inserted

Check if the proper CD is inserted

Make sure the working CD is music and it is not distorted, cracked, dirty, scratched or defected.

Standard: Working music CD

Description:

Semi-transparent CD or CD of strange shape can not be played.

Music CD recorded in PC CD-ROM and recorded CD-R can not be played.

Adapter is not needed to play 8cm CD.

Abnormal: There is something wrong with CD

Normal: Check and insert a proper CD

(3) Check and insert a proper CD

Check and insert a proper CD.

Check if CD is installed in reverse order.

Standard: No

Abnormal: Install the disc correctly

Normal: Clean the disc

Tester Connection

Condition

Standard Status

+B - GND

Constant Status

～

14V

ACC - GND

Ignition switch ACC or ON

～

14V

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands