manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 331

324

(II) Engine Hood

Engine Hood Removal / Installation

For engine hood installation, see the figure

1. Removal

Warning

•

It is dangerous to remove the engine hood without support. The engine hood may drop and

result in body injury. Work with at least one assistant when removing the engine hood and

should follow the procedures below:

1

Disconnect windshield washer hose.

2

Lift up the engine hood and support it with the spring brace;

3

Remove 2 spring braces under the help of the assistant to prevent the engine hood from dropping down

and resulting in body injury;

4

The assistant lifts the engine hood, removes the engine hood hinge bolt and the engine hood;

5

Remove the ventilator louver and remove the hinge arm;

6

Remove the hinge arm bracket attach bolt. Remove the hinge arm bracket from the body;

7

Remove the engine hood lock;

8

Remove the engine hood lock control cable.

2.Installation

1

The installation is in the reverse order of the removal;

2

Adjust the engine hood;

Engine Hood

Gas Spring Brace

Engine Hood Hinge 

Engine Hood Lock Control Cable

Engine Hood Lock

Engine Hood Installation Illustration

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands