manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 102

95

Replacement

1. Remove the reservoir hose 1 and reservoir hose 2

Notice: Clutch hydraulic control system and hydraulic

brake system share the reservoir. Prevent the brake

fluid from overflowing when removing the reservoir

hose.

2. Disconnect the connection with the pedal

Remove the lock pin, flat washer, pin shaft to separate the clutch hydraulic control master cylinder from

the clutch pedal

3. Remove the connecting pipe

Loose the threaded connector connecting pipe and the clutch master cylinder. Remove the connecting

pipe.

4. Remove the clutch pedal assembly

Remove the nuts, bolts, 2 bushing, sleeve, clutch pedal assembly

5. Remove the hydraulic hose

Loosen the union thread connecting clutch hydraulic hose and pipe. Remove E-shaped clip plate fixing

the both ends of the clutch hydraulic hose

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands