Geely CK MR479Q 2007 Workshop Manual Download Page 96

Page: 96 / 392

6. Separate the manual shift assembly from the transmission control cable assembly

(1) Remove the E-shaped clip plate between the transmission control cable assembly and manual

shift assembly

(2) Remove the cotter pin and flat washer between the selector cable and shift assembly

(3) Remove the locking nut connecting the cable and the shift assembly

7. Installation is in the reverse order of the above operation

Notice:

(1) All the E-shaped clip plate and lock pins should be assembled correctly. Otherwise, the

shifting will be impacted.

(2) The shift device cushion should be correctly assembled. Otherwise, it will affect the seal

effect

(3) Torque of the 4 nuts attaching the shift assembly to the floor: 20~25N.m

(4) The set nut attaching the selector control cable to the shifter shall be adjusted properly

(if the set nut is improperly adjusted, the shift operation will be affected), when in neutral

shift, the shift lever shall be in correct position (you must check whether the shift control

is flexible and reliable in the meantime), after the adjustment is completed, tighten the

two nuts

(5) Make sure the shift number words on the top of shift lever ball face towards the driving

direction of the vehicle, properly tighten the set screw of the shift lever

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands

Geely CK MR479Q 2007, Workshop Manual

Search results

Summary of Contents for CK MR479Q 2007

Reviews:

Brands by name

Popular brands