manualshive.com logo in svg

Geely CK MR479Q 2007, Workshop Manual

Share
Download
Geely CK MR479Q 2007 Workshop Manual Download Page 113

106

Section 3 Front Wheel Alignment

Adjustment

1. Inspect tire

2. Inspect toe-in

Toe-in

If the toe-in is not as specified, adjust the tie rod (but the left and

right tie rods must be adjusted symmetrically).

3. Adjust toe-in

(1) Loose the tie rod end lock nut.

(2)  Turn the left and right tie rod in the same direction for same

revolutions.

Hint: Adjust the toe-in to the specified value. 

Only adjust the one-side tie rod is not allowed.

(3) Make sure the left and right tie rods are of the same length.

(The difference should be less than 0.5mm).

(4) Tighten the lock nut of tie rod.

Torque: 45~50N.m

4. Inspect wheel limited turn angle

Turn the steering wheel fully and measure the turning angle.

Wheel angle:

If the wheel angle is less than the specified value, check whether the length of the right and left tie rod

ends.

Tire Pressure

220KPa

Toe-in

C-D: 0±3mm

Inside wheel angle

37.6°

Outside wheel angle

33.3°

Front

Front

Turn Left 

Inner 

Outer

Summary of Contents for CK MR479Q 2007









































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands